RIFF JTAG - Samsung GT-B7330 Omnia PRO Boot Repair Supported

ORT-JTAG - Spring Updates #1
ORT - JTAG UPDATE
[07 Apr 2011]

Description :
ORT Plus V1.35
Micromax C111 Repair Dead Boot
Samsung A877 Repair Dead Boot
Samsung T919 Repair Dead Boot
Samsung S5250 Repair Dead Boot / Repair Dead WIFI


What's new in ORT Plus V1.35 ?
QSC 6020 [0x200BF0E1]


Released Stuffs :

ORT Plus V1.35
Micromax C111 JTAG Pinout
Micromax C111 Dump File
Micromax C111 Instructions
Samsung A877 JTAG Pinout
Samsung A877 Dump File
Samsung A877 Instructions
Samsung T919 Dump File
Samsung T919 Instructions
Samsung GT-S5250 Dump File
Samsung GT-S5250 Repair File
Samsung GT-S5250 JTAG Pinout
Samsung GT-S5250 Instructions
Samsung GT-S5250 SM


Full Flashes Uploaded :

Download A877_FULL_RAW.rar
Download P1000_512MB_FULL_GOOD_RAW.rar
Download S8500_0x00000000_512M_RAW.rar
Download S8530_FULL_RAW.rar

ORT is a Real JTAGger's choice
www.ort-jtag.com/
www.gpgort.com/

07.05.2011 LG CU720 Shine Unbrick – Boot repair supported


Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect LG CU720:
Solder JTAG cable to LG CU720 JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG CU720 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

RIFF JTAG - CDMA Day Again !
09.05.2011 RIFF JTAG – CDMA Day Again ! More power for Indian users !

Whats new:
Added Huawei CDMA models support :
Huawei C2823 Repair, Read/Write NOR flash
Huawei C2809 Repair, Read/Write NOR flash
Huawei C2808 Repair, Read/Write NOR flash
Huawei C2807 Repair, Read/Write NOR flash
Huawei C2607 Repair, Read/Write NOR flash
Huawei C2905 Repair, Read/Write NOR flash
Added ZTE CDMA Model :
ZTE C335 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

RIFF JTAG - CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported

10.05.2011 CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported



Resurrecting LG VM265 is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect LG VM265:
Solder JTAG cable to LG VM265 JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG VM265 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.



Resurrecting Huawei EC1260 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
At resurrection startup you can select which zones are to be re-flashed. Thus you can save a lot of time if you know approximately which zone is damaged. Select EFS or MMC areas to be flashed only in case you are sure those are damaged – these areas quite big in size; unnecessary reflash is just a waste of time.
Please note, if you chose EFS to be repaired, an original ESN will be lost and substituted with the one contained in resurrection data. Current resurrector does not support ESN repair.


To resurrect Huawei EC1260:
Solder JTAG cable to Huawei EC1260 JTAG pads;
Insert Huawei EC1260 modem into any USB port for power;
Make sure Huawei EC1260 is selected in the list of models;
Click Resurrect button;
After Selection Dialog popup choose zones to be flashed;
Wait till software signals a successful operation completion;
De-solder JTAG wires;




Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

RIFF JTAG - More CDMA Models, Samsung S5250 Unbrick supported

29.05.2011 More CDMA Models, Samsung S5250 Unbrick supported


New CDMA models added today :
ZTE S160
Unicare UN510BF
Unicare ChivaC2
Huawei C5100
Samsung phones :
Samsung S5250
Samsung S5260 (Bug Fix)
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

Here is short list of latest news :

RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported « RIFF Box – JTAG Revolution

Other names for this device :
I-Mate JASJAR (HTC Universal)

Dopod 900 (HTC Universal)

O2 XDA Exec (HTC Universal)

T-Mobile MDA Pro (HTC Universal)

Orange SPV M5000 (HTC Universal)

Qtek 9000 (HTC Universal)

Grundig GR980 (HTC Universal)

Vodafone VPA IV / v1640 (HTC Universal)

Bug fix updates :

HTC_Wildfire.dll

- Added feature to flash RECOVERY and BOOT zones during resurrection.
- Added code reading option
HTC_WildfireS.dll
- By mistake was released DLL for usual HTC Wildfire model. Now is ok.

Thanks to Tatek and Basar for help. Free beers for both
Qualcomm Partition tool 1.04 :

Added support for 4kb page code reading (Applies to HTC Models)
In case You want to read unlock code from dump with 4kb page, and You get "Simlock zone is not found" message, tick "Don't adjust HTC Partition for 4kb NAND pages" check box, and read partition again.

Beta testers required for Samsung Galaxy S II :

Samsung Galaxy S2 i9100 wanted for beta test ! ! !

Support for Exynos 4210 Samsung CPU is added, and will be released after tests.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution